Global FAQ

Know everything about the world

Can you feed a panel from the bottom?

September 9, 2022 Chris Normand

Chief Moderator. Yes, you can bottom feed a panel.

Does main breaker have to be on top?

The NEC code provision that a breaker “ON” must be in the up position means that most panels can only use half of the breaker slots if mounted sideways.

Can I feed a sub panel from a sub panel?

Can I run a subpanel from a subpanel? Generally speaking, yes. You could put a million subpanels in series, and by itself that wouldn't be a code violation. The metal conduit can act as the equipment ground so a 4th wire is not required.

Can I feed a 100 amp sub panel from a 200 amp service?

Of course you can, you can add the 100 amp breaker to your 200 amp as long as it isn't overloaded, to start adding the subpanel you must first calculate how many yards it will be from the main panel to the subpanel, there is a formula that calculates how much friction will be on the wire at the connecting distance, …

Can I make my main panel a sub panel?

There's no problem with having a main breaker in a subpanel. It's required if your panel is in a separate building and has more than six breakers, but there's nothing prohibiting it in any other case.

What causes a 200 amp breaker to trip?

There are a number of reasons why the main breaker might trip. Lightning strikes, power surges from the utility company, or an overload to the electrical panel can all cause the main breaker to trip.

What is the 6 breaker rule?

The “six breaker throw rule” was a requirement in the National Electrical Code that a service must have have a main disconnect that shuts off all power and it cannot take more than six switch throws to do it, and the main disconnect(s) also must be clearly marked, as in the photo above.

See also Where is the world's tallest water coaster?

How many amps can you have on a 100 amp service?

For example, a 100-amp service panel could have circuit breakers that add up to more than 200 amps. This is normal.

How far can a subpanel be from the main panel?

You must provide from 3 to 4 feet of clearance on all sides of the panel depending on the voltage to ground. You may not know this voltage, so it’s best to provide 4 feet. The panel must be easily accessible, so don’t install it too far above the floor; 4.5 to 5 feet is about right.

Do sub panels need to be grounded?

The sub panel neutral bar or terminal should not be bonded to the enclosure or the ground of the sub panel. The sub panel ground should not have a ground rod tied to it. The bonding for the main ground sources such as a ground rod is made at the main panel where all the grounds are bonded together as well.

How many 100-amp breakers can you put in a 200 amp panel?

Nothing inherently wrong with 2 100A breakers in one box plus lots of other breakers – i.e., oversubscribing the 200A total is perfectly fine if real-world usage will stay under 200A.

How many double breakers are allowed?

Up to 8 tandem circuit breakers can be used. BR1212B100 = 12 spaces, 12 total circuits allowed. Tandem circuit breakers are not allowed.

How do you remove Sharpie from electrical panel?

Rubbing a pencil eraser over the marker can sometimes do the trick. Isopropyl alcohol also removes permanent marker from plastic. Simply wet a cotton ball with alcohol and rub it in circular motions until the stain disappears.

See also How do you temper hardened blades?

What does G mean in electrical terms?

G – Conductance, the inverse of electrical resistance (R) GFCI – Ground Fault Circuit Interrupter, a type of circuit breaker. H – Gross Head, determining the maximum power that can be produced. h – Net Head, also known as effective head.

Why is my main breaker warm?

It’s natural for circuit breakers to produce some heat, due to the fact that electrical resistance is constantly passing through its contacts and bimetal trip device. During normal operation, the sides and back of the system will reach higher temperatures than its knob.

How long do circuit breakers last?

How Long Do Circuit Breakers Last? According to the Consumer Product Safety Commission (CPSC), the lifespan of electrical breakers is typically between 30-40 years. Electricity issues such poor power ratings or fluctuating voltages are all factors that will affect how long your circuit breaker lasts.

Where is my main breaker?

In most cases, this will be located outside your home near your electric meter, but in older homes, you may find it inside. The main breaker will be the largest breaker in the panel.

How many service disconnects can you have?

Multiple disconnects

You can have no more than six service disconnects for each service permitted by 230.2. This rule also applies to each set of service-entrance conductors permitted by 230.40, Exception No. 1, 3, 4, or 5 [230.71].

How many amps are lethal?

While any amount of current over 10 milli- amperes (0.01 amp) is capable of producing painful to severe shock, currents between 100 and 200 milliamperes (0.1 to 0.2 amp) are lethal.

See also What happens if you accidentally shower with contacts?

How far can a sub panel be from the main panel?

You must provide from 3 to 4 feet of clearance on all sides of the panel depending on the voltage to ground. You may not know this voltage, so it’s best to provide 4 feet. The panel must be easily accessible, so don’t install it too far above the floor; 4.5 to 5 feet is about right.

Leave a Reply Cancel reply