The F-01 error code indicates a primary control failure. The primary controls are located inside the main control panel where the dryer cycles and settings are displayed. Any burns or arcing on the motherboard where the wires are connected could mean the primary control was shorted out.
What does F mean on Whirlpool dryer?
How do I fix F01 error?
Your dryer might display the F01 error code when the door switch is defective, or it might be sending a faulty signal to the control panel. To check the door switch: Make sure the power is still switched off and you've removed the dryer panels.
What does F mean on Kenmore dryer?
What does F 40 mean on a dryer?
What does code E01 mean on Whirlpool washer?
November 2, 2021. A Whirlpool washer error code E01/F06 indicates that the washer’s motor control unit (MCU) is having trouble communicating with the washer’s central control unit (CCU). In most cases, the issue is caused by a damaged MCU circuit, usually caused by an overload.
Why does my washer say E03?
The machine is unable to drain the water away
Should the error code E3 appears it is warning that the machine is not draining. You can easily fix this problem by removing any blockages from the drain pump situated at the front of the machine for easy access.
What does E03 mean on a washing machine?
An E03 error code means that your washing machine has encountered a draining problem.
Why does my dryer say F1?
If your Whirlpool dryer is displaying an F01 error code, this means there is something wrong with the control board or one of the components connected to it. It is commonly caused by a power failure or after a power surge occurs.
Why is my dryer flashing F1?
the F01 indicates a failed electronic machine control board. First try to reset your washer by unplugging your dryer for a while. then plug it back in and see if you still get that error. If the error code returns after plugging the dryer then the electronic machine control board will need to be replaced.
Why is my Samsung dryer blinking?
60 min is blinking or Extra Low light is blinking
When either of these lights are blinking, this means that the dryer is getting too hot. The most common cause is a clogged lint screen or vent system trapping heat in the dryer. Clean the lint screen, vent system, or both to correct the error.
How do I clear the CL9 code on my Samsung dryer?
On this unit, the error code CL9 indicates the child lock feature is activated. Press the temp and and time buttons and hold them for 3 seconds.
What does F9 mean on washing machine?
Drain hose
If the drain hose is kinked, crushed, or clogged, it will affect the washer’s ability to drain and potentially cause the E1/F9 error code. The drain hose not being installed correctly could also cause the error code.
What does code F9 mean on a Whirlpool stove?
This code will most often indicate that the appliance is wired incorrectly at the home electrical supply or the hardwire connection. If your range was installed recently and is not functioning, contact a qualified electrician to verify the electrical supply.
What does F mean in washing machine?
The F indicates that the washer control detected a component problem. Since the door remained locked, your likely problem was with the drain pump or excessive suds preventing the washer from draining out the water properly.
What does F mean on a Whirlpool?
An F error code usually means the washer will not work at all, and the control board will need to be replaced.
What does F1 mean on Whirlpool washer?
Usually, it’s a problem with the control board. By replacing the control board, you should be able to fix the problem. However, it might also be a problem with the hose, something might be stuck in the hose.
What does F01 mean on a Whirlpool washer?
The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. …
What does E08 mean on Hoover washing machine?
If you put too many clothes in the drum and overload the machine it may result in error code E08 being displayed. Should this occur then reduce the load size by removing some of the garments in the drum and try again.
What does code E1 mean on Whirlpool dryer?
Common solutions for: Whirlpool E1, E2 – Thermistor Failure
This error code is indicating that the exhaust air temperature is either below 18 degrees Fahrenheit or above 250 degrees Fahrenheit. Check the thermistor with an Ohm meter, if it reads >50k Ohms (E1) or less than 500 Ohms (E2) it is defective.