An F error code usually means the washer will not work at all, and the control board will need to be replaced.
How do you fix a code F on a Whirlpool washer?
If there isn't a control board failure, the machine will self-assess and reset while unplugged. Next, plug in the washer and hold the START and PAUSE buttons at the same time for 1 minute. This simple exercise should clear the error code.
What does an F mean on a washing machine?
What does code F mean?
What does E01 mean on a washing machine?
E01 – there’s an issue with the lock, its wiring or connection to the control board. Check the door is closed properly and the wiring is intact.
What does F11 mean on Whirlpool washer?
The infamous and all-too-common F11 error code in these Whirlpool Duet front load washers is a case-in-point. The tech sheet inside the washer says this is a communications error between two control boards: the CCU (central control unit) and MCU (motor control unit).
Why is my Kenmore washer flashing F?
Reset the FH error code by removing the washer’s power source. The FH error code on your Kenmore Elite washing machine is an indicator that there is a problem with incoming water. When there is little water coming into the machine, the FH code will appear and the washer will stop.
How do I open the door on my Whirlpool Duet washer?
- Reach up inside the front panel and locate the door latch assembly on the right side of door.
- Feel for a tear-drop shaped tab on the bottom of the door latch assembly. This tab will manually unlock the door.
- Gently pull down on tab about 1/4 inch or until you hear a click.
- Reach up inside the front panel and locate the door latch assembly on the right side of door.
- Feel for a tear-drop shaped tab on the bottom of the door latch assembly. This tab will manually unlock the door.
- Gently pull down on tab about 1/4 inch or until you hear a click.
Why does my washer say F?
An F error code usually means the washer will not work at all, and the control board will need to be replaced.
What does F 51 mean on a washer?
When your washer is overloaded, the rotor cannot spin the washer drum around correctly, and an F51 error code will result. To check if your washer is overloaded, make sure that it isn’t overly full (more than 80% full to the top), and if it is, remove some items and then try to turn your washer on again.
What does E3 mean on a Whirlpool washer?
E3 – Unbalanced alarm
If you receive an E3 Error code, your washer may be unbalanced. This could be caused by the washer being too tightly packed, or clothing not distributed evenly. This will usually occur during the spin cycle. Stop the spin cycle.
What does 5d mean on a Whirlpool Cabrio washer?
A Whirlpool Cabrio 5d error code means the same thing as an Sd or Sud error code; the washer is detecting too many soap suds.
What does F9 mean on a Whirlpool washer?
Often when a Whirlpool washer displays an E1/F9 error code, it is the drain pump that is causing the error code. The drain pump can become defective if it is clogged, the impeller breaks, or if an electrical fault causes the pump to fail.
What does F6 mean on a Whirlpool washer?
A Whirlpool washer error code E01/F06 indicates that the washer’s motor control unit (MCU) is having trouble communicating with the washer’s central control unit (CCU). In most cases, the issue is caused by a damaged MCU circuit, usually caused by an overload.
What does F1 mean on Maytag oven?
The Maytag oven F1 error code indicates the touchpad or control board (clock) on your oven is faulty. Refer to your owner’s manual on how to test for a faulty touch pad and how to replace the touch pad, control board, or both.
What does F1 mean on a Maytag washer?
The F1 E1 alert indicates there is an issue with the appliance control unit or associated wiring. Unplug the washer, wait two minutes, then plug back in.
What does F35 mean on a Kenmore washer?
The F35 error code indicates an analog pressure sensor error. The analog pressure sensor is the component that detects water level in the washer tub. This error can usually be cleared but it will occur again if the main control board still detects a problem with the signal from the analog pressure sensor.
What does E1 mean on Kenmore washer?
If the washer tub fills with water when the E1 error code appears, then a disconnected or broken air hose might be preventing the water level sensor from detecting water level correctly. Check the air hose connections on the bottom of the washer tub and the water level sensor and reconnect the hose if disconnected.
Why does my washer say F 21?
The most common causes of the F21 error code are: The drain pump has a blockage or is faulty and needs to be replaced. The drain filter on the drain pump is blocked or clogged.
What does it mean when Whirlpool washer says LoC?
There is no Error – Control Lock is activated
If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock, and need to de-activate it to allow the washer controls to function.
What is 5d on Whirlpool washer?
Did you receive an Sd (may appear as 5d) or Sud Error Code? If Sd or Sud (excess suds) appears in the display, you have excessive suds in washer. The washer is running a suds reduction routine. Allow the washer to continue.