What does F9 mean on Whirlpool washer?

Often when a Whirlpool washer displays an E1/F9 error code, it is the drain pump that is causing the error code. The drain pump can become defective if it is clogged, the impeller breaks, or if an electrical fault causes the pump to fail.

How do I fix E1 F9 on my Whirlpool washer?

How do I fix F9 error on my washing machine?

How do I clear the error code on my Whirlpool washer?

What does E01 and F09 mean on a Whirlpool washer?

What does code 5d mean on Whirlpool washer?

A Whirlpool Cabrio 5d error code means the same thing as an Sd or Sud error code; the washer is detecting too many soap suds. Whirlpool does not actually list 5d as an error code; instead, people misinterpret the Sd error code as reading 5d.

Why is my Whirlpool washer door locked?

The most common cause of a Whirlpool washer door being locked and not being able to open is a faulty lid switch (including the striker). The door switch locks and unlocks your door depending on which stage your wash cycle is at. When it becomes defective, your washer door may not unlock when it’s supposed to.

How do I unlock the door on my Whirlpool Duet washer?

Pull down on the bottom panel and pull it away from the washer. Reach through the open panel and up to the door lock. Find the release ring below the locking mechanism. Pull down on the ring to unlock the door.

What are the most common problems on a Whirlpool washing machine?

What does F mean on dryer?

The F-01 error code indicates a primary control failure. The primary controls are located inside the main control panel where the dryer cycles and settings are displayed. Any burns or arcing on the motherboard where the wires are connected could mean the primary control was shorted out.

What does F01 mean on a washing machine?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. … Be sure to unplug the washer before accessing internal components.

What does F21 mean on a washer?

October 4, 2021. If your Whirlpool washer has an F21 error code, it indicates that your washer has a drainage problem. The good news is the issue can usually be resolved by simply clearing the drain filter or drain hose.

What does E1 and f3 mean on a Cabrio washer?

The error code F03/E01 indicates a problem with the water level. If your washer doesn’t get enough water, it will not be able to work correctly. Most of the time, this error code is a result of a faulty sensor, hose, or brand pipe. Now that we know what the error code means, let’s try to fix it.

How do I unlock my Whirlpool top load washer without power?

Accessing a Top-Loading Washer. Push the Start/Stop button to unlock the washer door during the spin cycle. Pause the machine by quickly pressing the Start/Stop button once. After a few seconds, the washer will halt and you’ll hear the door unlocking.

How do I unlock my Maytag washer?

Washer door unlock fix: Cancel the wash cycle, wait for it to drain the water and the door should unlock, OR pull the green string near the detergent area, OR pull the lever on the bottom of the door switch, OR unplug the washer for 5 minutes to reset. These 4 things should unlock your washers door.

Why does my washer say F 21?

The most common causes of the F21 error code are: The drain pump has a blockage or is faulty and needs to be replaced. The drain filter on the drain pump is blocked or clogged.

What does LoC with a red key mean on Whirlpool washer?

If you try to push buttons, you may see the code “LoC” or “LC” (depending on your model). This is a reminder that you have set the control lock, and need to de-activate it to allow the washer controls to function.

Are old washing machines better than new ones?

Older machines are heavier and were built to last. Because they were constructed with greater quality materials, they typically have a much longer lifespan than the new washers built today.

How long does a Whirlpool Cabrio washer last?

It does not do more than the average 8 loads of laundry per week that whirlpool statistics suggests an average household does. Whirlpool also says the lifespan of a Cabrio washer is 11 1/2 years, that’s comical, if you’re easily entertained by bad jokes.

How do I fix my Whirlpool F01?

To reset your Whirlpool dryer’s main control, simply unplug your dryer from its power source. This will reset the main control. It is recommended that you wait a few minutes before you plug it back in. After it has been reconnected to its power source, turn it back on and see if the error has been resolved.

What does F01 mean on a Whirlpool washer?

The F01 indicates a failed electronic machine control board. This error code can sometimes be caused by a glitch or power surge through the electrical lines. You may be able to clear this code by unplugging the washer for 5 minutes. …