Why does my microwave say C-10?
Error code C-10 / C-20 / C-F0 / C-F1. Do you see one of the error codes mentioned above on the display of your microwave? There’s something wrong with the temperature sensor. Pull the plug out of the socket.
What does C-10 mean on a microwave?
Error with gas/easy/PH sensor.
What is c10 on Samsung microwave?
What does C do mean on microwave?
How do I reset my Samsung microwave?
What does F1 mean on a microwave?
F1. Open Thermal Sensor, due to excessive heat in microwave cavity.
What is se error in Samsung microwave?
The SE error code on a Samsung microwave means there is a problem with the touchpad or control board. In most cases, the error is caused by a stuck button or a dirty ribbon cable. In more serious cases, the control board may have a fault that can only be fixed by replacing the control board.
Why does my microwave say E-11?
The Samsung microwave error code E-11 indicates a humidity sensor issue. To locate the humidity/gas sensor or the wiring harness, check on the top left side of the microwave. It is located under the outer panel.
What is error code e 11 on Samsung microwave?
What is the meaning of the Samsung microwave error code E-11? This error code indicates that there is a problem with the humidity sensor. On the left, you can see the sensor that is located above your oven.
Why has my Samsung microwave stopped working?
If your microwave is not working or has stopped working, there could be a few reasons why. A microwave that is not turning on or is turning off by itself is usually caused by overheating or a low power supply. However, if your microwave doesn’t heat up at all, it could be in Demo mode.
Why did my Whirlpool microwave stop working?
Verify the power cord is connected to a grounded, operational outlet. Check the outlet. If you are unaware if it’s working, plug in a household lamp or other small appliance to verify that the outlet is working. Check to see if a household circuit breaker has tripped or if the household fuse has been blown.
What does 5E mean on a Samsung oven?
Similarly, Samsung stove error codes
The control panel sensor has been on for too long, according to a SE/5E error warning on a Samsung ceramic hob’s display.
What does E 83 mean on a Samsung microwave?
e-83 indicates a door switch or control board failure.
Why does my microwave say C-10?
This is caused by the sensor’s hardware limitation and is not an actual defect. If the C-10 error code appears while running the test but the oven is heating normally, the code can be ignored. This error does not effect the oven’s usability or performance.
What does it mean when a microwave says se?
When the SE error code appears on a Samsung Microwave it indicates that your unit has a key that’s stuck on the control pad or ribbon cable connection is dirty or the electronic control board has failed.
Why did my LG microwave stop working?
It could be due to one of several common problems. The microwave’s magnetron or capacitor may be defective, the fuse may have blown, or there may be an issue with one of the other components.
What voltage does a magnetron use?
Operation of Magnetrons
This supply can provide an AC or DC voltage, with typical voltages ranging from 2.5 V to 15 V, and currents ranging from a few A to 100 A and above. The filament voltage has to be applied some time before the cathode voltage so the filament has sufficient time to pre-heat.
Why won’t my LG microwave heat up?
If the water did heat, there are three explanations about why the microwave is not heating as expected: The power level might have been set too low. The timer function could have been activated by mistake which does not heat the microwave, but only works as an alarm. A wrong sensor cook settings may have been used.
What does E0 mean on Kitchenaid refrigerator?
F1-E0 – EEPROM Communication Error – Disconnect power for at least 30 seconds and then reconnect. Allow at least a minute after power has been restored and if error code reappears, replace control board (clock).
Why is my microwave saying se?
One of the most common error codes that Samsung microwaves display is “SE.” The SE error code can usually be solved by either resetting your microwave, replacing the control panel, or replacing the control board.